<br><font size=2 face="Courier New">&gt;&gt;Hrm. I dont know how different this is to the older AP-1000, its features<br>
&gt;&gt;are a bit different. The Avaya guy I was speaking too said that they have<br>
&gt;&gt;a bridge mode, but only to another AP-3, and that it wasnt a client mode<br>
&gt;&gt;as such, so you couldnt attach it to another network as a client.<br>
</font>
<br><font size=2 face="sans-serif">The AP3 is actually equivalent to the orinoco AP2000. In a remote distribution situation (ie where the avaya is also a client to another ap), bridging the wlan i/fs requies a WDS capable ap at the other end.</font>
<br><font size=2 face="sans-serif">Another way to skin that cat is to have both i/f's functioning as AP's and have your backbone feed as a client of one of them.</font>
<br>
<br><font size=2 face="sans-serif">On a side note, we successfully tested a dlink 900+ as a client to an avaya AP3 on saturday (over 37km even!).</font>
<br>
<br><font size=2 face="sans-serif">Darren Dreis<br>
Vice President</font>
<br><font size=2 face="sans-serif">Melbourne Wireless Inc.<br>
vicepresident@wireless.org.au</font>
<br><font size=2 face="sans-serif">http://www.wireless.org.au<br>
</font>
<br>
<br>
<br>
<table width=100%>
<tr valign=top>
<td>
<td><font size=1 face="sans-serif"><b>Jamie Moir &lt;jmoir@jmcs.net.au&gt;</b></font>
<br><font size=1 face="sans-serif">Sent by: owner-melbwireless@wireless.org.au</font>
<p><font size=1 face="sans-serif">19/05/2003 10:57 AM</font>
<br>
<td><font size=1 face="Arial">&nbsp; &nbsp; &nbsp; &nbsp; </font>
<br><font size=1 face="sans-serif">&nbsp; &nbsp; &nbsp; &nbsp; To: &nbsp; &nbsp; &nbsp; &nbsp;melbwireless@wireless.org.au</font>
<br><font size=1 face="sans-serif">&nbsp; &nbsp; &nbsp; &nbsp; cc: &nbsp; &nbsp; &nbsp; &nbsp;</font>
<br><font size=1 face="sans-serif">&nbsp; &nbsp; &nbsp; &nbsp; Subject: &nbsp; &nbsp; &nbsp; &nbsp;Re: [MLB-WIRELESS] Avaya AP-3</font></table>
<br>
<br><font size=2 face="Courier New"><br>
On Mon, 19 May 2003 darrend@ndpgroup.com.au wrote:<br>
<br>
&gt; &gt;&gt;Can it be an access point and a bridge at the same time (with two cards)<br>
&gt; ?<br>
&gt;<br>
&gt; Yes, you can bridge both wlan interfaces in any mode (eg AP bridged to ptp<br>
&gt; link, or AP bridged to AP for load balancing)<br>
<br>
Hrm. I dont know how different this is to the older AP-1000, its features<br>
are a bit different. The Avaya guy I was speaking too said that they have<br>
a bridge mode, but only to another AP-3, and that it wasnt a client mode<br>
as such, so you couldnt attach it to another network as a client.<br>
<br>
Regards,<br>
<br>
Jamie<br>
<br>
<br>
<br>
<br>
<br>
To unsubscribe: send mail to majordomo@wireless.org.au<br>
with &quot;unsubscribe melbwireless&quot; in the body of the message<br>
<br>
</font>
<br>
<br>