[MLB-WIRELESS] SVEC FD1811 (aka WLAP) Firmware

[Tom Parker]

MessageSorry,  I looked at the wiki finally.  There is an SMD Atmel flash
chip in the lower right corner of the image.

I can read this for you, but it will be hard to get off the board (all pins
will need to be straight and clean to fit in the programmer).

Cheers,
Tom

----------------------------------
Tom Parker tparker at netspace.net.au
http://www.wiresncode.com/projects



  -----Original Message-----
  From: owner-melbwireless at wireless.org.au
[mailto:owner-melbwireless at wireless.org.au]On Behalf Of Tom Parker
  Sent: Wednesday, 30 April 2003 6:51 PM
  To: 'Melbourne Wireless'
  Subject: RE: [MLB-WIRELESS] SVEC FD1811 (aka WLAP) Firmware


  Have you guys opened these up?  What kind of chip is the flash chip.

  I've got access to gear that can read/write just about any kind of
chip/package - but it might in involve some nasty soldering it is SMD.

  Cheers,
  Tom
  ----------------------------------
  Tom Parker tparker at netspace.net.au
  http://www.wiresncode.com/projects



    -----Original Message-----
    From: owner-melbwireless at wireless.org.au
[mailto:owner-melbwireless at wireless.org.au]On Behalf Of Fenn Bailey
    Sent: Wednesday, 30 April 2003 12:20 PM
    To: 'Melbourne Wireless'
    Cc: 'Dan Flett'
    Subject: RE: [MLB-WIRELESS] SVEC FD1811 (aka WLAP) Firmware


    I had a bit of a play with these (with Jamie's assistance) and basically
ran into exactly the same problem.

    You can see a bit of a summary here:
http://melbourne.wireless.org.au/wiki/?SVECWLAP

    By the looks of it, your findings should be added to this.

    One of the major issues is that they don't _appear_ to implement
standard TFTP - it looks like a slightly whacky variant, which doesn't speak
well for it fully implementing TFTP (eg: GET as well as PUT).

    The main hurdle is finding a working copy of the firmware. I don't know
if you found the same thing, but the ethernet port appears to completely die
when you flash them with Linksys firmware, which makes further TFTP flashing
somewhat difficult. However, the linksys USB client appears to flash it
fine.

    The best bet that I can think of is reverse-engineering the USB
interface to it (I imagine it would be quite simple) and seeing if you can
read the firmware out this way. I have had success doing this sort of thing
with DSL modems in the past (albeit via serial ports), but the principle is
much the same.

    Unfortunately, I don't have the time to fiddle with this at the moment,
but if anyone knows of good USB sniffing software, or a good way to do
this - it would be most appreciated.

    Cheers,

        Fenn.
      -----Original Message-----
      From: owner-melbwireless at wireless.org.au
[mailto:owner-melbwireless at wireless.org.au] On Behalf Of Dan Flett
      Sent: Wednesday, 30 April 2003 10:52 AM
      To: Melbourne Wireless
      Subject: [MLB-WIRELESS] SVEC FD1811 (aka WLAP) Firmware


      Hi all,

      I have a SVEC FD1811 AP which is rather sick since I flashed it with
Linksys firmware.  So to try to nurse it back to health I've been trying to
find any firmware which will make it work again.  I've noticed that the SVEC
FD1811 has many twin (ie rebadged) brothers sold by different suppliers.
But none of them offer a firmware download.  The SVEC AP, like many other
APs out there (including the Linsys WAP11 v1) uses the Atmel AT76c510
chipset.  Today I think I found an important difference between the SVEC and
most other 510-based APs.

      I found this site:

      http://www.toptrend.com.tw/Technical%20support%20for%20WLAN-1.htm

      As far as I can tell, Toptrend write the firmware for the Atmel
510-based APs.  Most of them have Intersil radio chipsets in them.  I
guessed this by looking at the firmware version number on the page above.
But the SVEC FD1811 (and I assume, all of the rebadged SOHO-WLAPs out there)
use RFMD radio chipsets.  The version number of the firmware listed on
Toptrend's site is the same as what is in my other, still working SVEC AP:
V0.0.1.16

      So can anyone suggest how I might get a hold of this firmware?  It
isn't available for download anywhere.  SVEC won't send it out.  I'm goint
to email Toptrend and see if they'll send it to me.  Jamie Moir and I have
tried to extract the good firmware out of a working SVEC AP using TFTP but
with no success. That's not to say it isn't possible though.  Is anyone
willing to devote a bit of time to tinker with my malfunctioning AP?

      Dan
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.wireless.org.au/pipermail/melbwireless/attachments/20030430/0f80b2a8/attachment.html>